|
iankellogg
|
 |
« on: March 22, 2014, 08:52:15 pm » |
|
I am preparing a large bulk order of caps to start preparing cap kits. Current kits that I have listed out are.
MTC9000
G07-CB0
K4600
K4900
K7000
20-EZ
XM-1801/XM-2001
MC2000
AGM-20M
19V2000
G05-802/GO5-805
G08-003
PM1718
20ez soundboard
Are there any kits I am missing that would be of interest to you please let me know. I'll place the order within the next 2 weeks as soon as I have the documentation and instructions done.
|
|
|
|
« Last Edit: November 11, 2014, 08:32:00 pm by iankellogg »
|
Logged
|
|
|
|
|
John's Arcade
|
|
« Reply #1 on: March 23, 2014, 08:43:19 am » |
|
I am preparing a large bulk order of caps to start preparing cap kits. Current kits that I have listed out are.
MTC9000
G07-CB0
K4600
K4900
K7000
20-EZ
XM-1801/XM-2001
MC2000
AGM-20M
19V2000
G05-802/GO5-805
G08-003
PM1718
20ez soundboard
Are there any kits I am missing that would be of interest to you please let me know. I'll place the order within the next 2 weeks as soon as I have the documentation and instructions done.
Ian, you're gonna start selling cap kits? Are you the new Bob Roberts?  |
|
|
|
|
Logged
|
|
|
|
|
arcadefan1985
|
|
« Reply #2 on: March 23, 2014, 09:01:38 am » |
|
How about specialty caps? Like some of the power caps on the chassis boards and Psu caps and transistors.
Just a suggestion.
|
|
|
|
|
Logged
|
|
|
|
|
iankellogg
|
|
« Reply #3 on: March 23, 2014, 09:48:12 am » |
|
Nothing wrong with becoming Bob Roberts
The only thing with specialty parts is getting enough to make the price worth while. As time goes on I will probably add stuff like that as it would benefit me personally.
|
|
|
|
|
Logged
|
|
|
|
|
jasonsmith
|
|
« Reply #4 on: March 23, 2014, 08:36:32 pm » |
|
How about kits for Atari's AR boards? If there's one thing I've learnt they are very important and cause a lot of issues. The AR II boards have more stuff so it should be easy enough to make kits for all.
Here is what I compiled for my Asteroids Deluxe AR I board:
2 x 10uf 25v axial
3 x 470uf 25v axial
1 x 1000uf 25v axial
2 x 3300uf 25v axial
1 x tip32
1 x 2n3055
1 x 1k ohm trimpot
I'm also going to change out the LM305 voltage regulator, it's getting hard to find though.
|
|
|
|
« Last Edit: March 23, 2014, 08:38:04 pm by jasonsmith »
|
Logged
|
|
|
|
|
iankellogg
|
|
« Reply #5 on: March 23, 2014, 10:09:22 pm » |
|
I'll take a look into the ar2 I have a few laying around. As for the lm305 you can use lm100 lm105 lm300 and lm305 but I was unable to find a drop in replacements using available chips.
|
|
|
|
|
Logged
|
|
|
|
|
STEVESPEEZE
Guest
|
|
« Reply #6 on: March 24, 2014, 02:47:10 am » |
|
How about specialty caps? Like some of the power caps on the chassis boards and Psu caps and transistors.
Just a suggestion.
http://www.johnsarcade.com/forum/index.php?topic=816.0This place carries whatever is not in a cap kit. |
|
|
|
|
Logged
|
|
|
|
|
iankellogg
|
|
« Reply #7 on: March 24, 2014, 07:07:59 am » |
|
Yeah I have been using that resource and a few others. I think he was talking about having the parts for sale for the more special parts that you don't normally replace. I don't mind the suggestion but they are not that cheap and more risky to have in inventory. I might revisit that position after I get set up more. At the moment I am still doing documentation.
For the cap kits I am trying to highlight and label all the Caps in a picture to make finding them easier.
Sent from my SM-N900V using Tapatalk
|
|
|
|
|
Logged
|
|
|
|
|
iankellogg
|
|
« Reply #8 on: March 25, 2014, 09:43:24 am » |
|
OKay dokey, I am putting in a test order for 10 kits. These are test kits because some of the 16v and 25v caps were bumped up to 50v and I am not 100% sure how they will fit, they should fit without issues since I did check the spacing and width but you can never be sure.
Price is $6 a kit and shipping is included. Please PM me if you want one. The list of current support kits is above. If there is anything wrong with the kit I will refund your money if you can send me a picture of it!
|
|
|
|
|
Logged
|
|
|
|
|
jasonsmith
|
|
« Reply #9 on: March 25, 2014, 10:09:23 am » |
|
PM on the way.
|
|
|
|
|
Logged
|
|
|
|
|
arcadefan1985
|
|
« Reply #10 on: March 25, 2014, 09:39:30 pm » |
|
I keep bulk cap's in my shop but for those who don't this is a hell of a  !! |
|
|
|
|
Logged
|
|
|
|
|
Level42
|
|
« Reply #11 on: March 26, 2014, 06:51:27 pm » |
|
What brand are they and what type of that brand ? Are they low ESR, 105 degr. ?
Caps are not just caps folks....at these prices I am suspecting cheap Chineses stuff....
|
|
|
|
|
Logged
|
|
|
|
|
iankellogg
|
|
« Reply #12 on: March 26, 2014, 08:49:01 pm » |
|
Almost all of the caps are Kemet with few exceptions. The caps are all 105C. I can provide a few list of caps used, its just long. I am completely willing to change these caps to improve the quality if it is suspect.
|
|
|
|
|
Logged
|
|
|
|
|
jasonsmith
|
|
« Reply #13 on: April 01, 2014, 09:21:46 pm » |
|
Ian do you have a guestimate on when you'll be ready to ship?
|
|
|
|
|
Logged
|
|
|
|
|
iankellogg
|
|
« Reply #14 on: April 01, 2014, 09:52:09 pm » |
|
As soon as the caps come in which should be i think thursday. Maybe Wednesday. The first set of instructions may not be the best but ill work on it.
|
|
|
|
|
Logged
|
|
|
|
|
