|
Title: Adjusting Horizontal positioning and size on a GO7 FBO Post by: Servo on March 10, 2014, 05:56:39 pm Can anyone tell me how to adjusting horizontal positioning and size on a GO7 FBO. i am running pac man ans it's not taking up the whole screen. I see V Height but nothing for the horizontal
Servo Title: Re: Adjusting Horizontal positioning and size on a GO7 FBO Post by: John's Arcade on March 10, 2014, 08:11:24 pm Can anyone tell me how to adjusting horizontal positioning and size on a GO7 FBO. i am running pac man ans it's not taking up the whole screen. I see V Height but nothing for the horizontal Servo Horizontal size will be adjusted with the horizontal width coil. You need a plastic allen wrench to adjust it when it's on. DO NOT USE A METAL ALLEN WRENCH unless the monitor is OFF. The horizontal position can be adjusted with the jumpers on the back towards the right of the chassis. (http://www.dragonslairfans.com/xevious/xevnam4.jpg) See the thing with the copper winding? That's the width coil: (http://www.pinrepair.com/g07/g07_02.jpg) Title: Re: Adjusting Horizontal positioning and size on a GO7 FBO Post by: Servo on March 10, 2014, 08:39:20 pm how do you adjust the jumper for the Horizontal center?
Title: Re: Adjusting Horizontal positioning and size on a GO7 FBO Post by: John's Arcade on March 10, 2014, 08:47:40 pm how do you adjust the jumper for the Horizontal center? You remove it and put in on the pin you want. Left Center or Right. However, it's not gonna do much. :) Your best bet is playing with the horizontal hold until you can get it where you want it without it freaking out. Do the jumper and mess with the hold. Title: Re: Adjusting Horizontal positioning and size on a GO7 FBO Post by: Servo on March 10, 2014, 08:58:20 pm need to get a set of those adjustment tools, ill see if my local radio shack has them tomorrow, thanks for the help
Servo Title: Re: Adjusting Horizontal positioning and size on a GO7 FBO Post by: John's Arcade on March 10, 2014, 09:02:51 pm need to get a set of those adjustment tools, ill see if my local radio shack has them tomorrow, thanks for the help Servo Yes, you need TV Adjustment tools. I got mine at Radioshack. They were on clearance a couple of years ago. Not sure if they will still have them. http://www.amazon.com/Universal-Color-Alignment-Tool-Set/dp/B005M6BY2A/ref=sr_1_1?ie=UTF8&qid=1394503360&sr=8-1&keywords=tv+adjustment+tools Title: Re: Adjusting Horizontal positioning and size on a GO7 FBO Post by: UnwoundS3GA on March 10, 2014, 10:54:45 pm need to get a set of those adjustment tools, ill see if my local radio shack has them tomorrow, thanks for the help Servo Yes, you need TV Adjustment tools. I got mine at Radioshack. They were on clearance a couple of years ago. Not sure if they will still have them. http://www.amazon.com/Universal-Color-Alignment-Tool-Set/dp/B005M6BY2A/ref=sr_1_1?ie=UTF8&qid=1394503360&sr=8-1&keywords=tv+adjustment+tools Title: Re: Adjusting Horizontal positioning and size on a GO7 FBO Post by: Servo on March 27, 2014, 09:18:29 pm so i got a set of adjustment tools and i tried but it seems that i can only make the image smaller with the horizontal coil, when i go the apposite way it dose noting. the image will not get any larger, could that mean i need to replace the horizontal size coil? any advice on this one guys would be appreciated...
Servo Title: Re: Adjusting Horizontal positioning and size on a GO7 FBO Post by: VertexGuy on March 27, 2014, 10:19:33 pm so i got a set of adjustment tools and i tried but it seems that i can only make the image smaller with the horizontal coil, when i go the apposite way it dose noting. the image will not get any larger, could that mean i need to replace the horizontal size coil? any advice on this one guys would be appreciated... Servo that may be a cap. There is a certain cap that goes bad and makes the screen narrow. i think its C47 or something (http://i1203.photobucket.com/albums/bb392/turbografx/1604496_778095445552241_1211706108_n.jpg) (http://s1203.photobucket.com/user/turbografx/media/1604496_778095445552241_1211706108_n.jpg.html) Title: Re: Adjusting Horizontal positioning and size on a GO7 FBO Post by: Servo on March 28, 2014, 07:54:55 am i just recapped the monitor, i think your referring to C407,i changed it, im going to order a new coil today but would love here any other suggestions.
servo Title: Re: Adjusting Horizontal positioning and size on a GO7 FBO Post by: John's Arcade on March 28, 2014, 10:15:06 am so i got a set of adjustment tools and i tried but it seems that i can only make the image smaller with the horizontal coil, when i go the apposite way it dose noting. the image will not get any larger, could that mean i need to replace the horizontal size coil? any advice on this one guys would be appreciated... Servo Those coils have a high failure rate. Bob sells replacements and they are included in the deluxe cap kit. Title: Re: Adjusting Horizontal positioning and size on a GO7 FBO Post by: Servo on March 28, 2014, 11:43:19 am i just got an order from bob yesterday, oh well
|