|
Title: Nintendo VS products and Services from PC-10.com Post by: Joe3693 on November 26, 2020, 09:54:47 pm First is the all new VS Top Gun Castlevania Switcher
(https://uploads.tapatalk-cdn.com/20201127/9ad1927bfb0d6aa309950db65e0ebea0.jpg) The switcher currently only works on a Top Gun Daughtercard with a Top Gun RC2C05-04 PPU and allows you to switch between Castlevania and Top gun. Simple design allows you to remove a single eprom and install this in its place. You must have a Top Gun Daughtercard and a main VS PCB, this is an add on card for them. The picture below show how it is installed. Again no main pcb or Top Gun daughtercard is included. $50 shipped in the US. International shipping is additional. (https://uploads.tapatalk-cdn.com/20201127/3791a0c30cdad742f7f25049f5dcdd5f.jpg) Next is the Goonies Gradius Switcher. This has been around for a few years now. It takes the place of the two EPROMS on your existing Vs. Goonies or Vs. Gradius daughtercard and will now allow you to play both games on the same board. There is a simple push button switch that will allow you to switch between games**. You will no longer need two separate daughercards to play these two great Vs. titles!!!Also $50 shipped in the US. International additional. (https://uploads.tapatalk-cdn.com/20201127/88e4389988bf98cbf59cbdcf131016e9.jpg) Nintendo Vs. Chipsets: $20 plus shipping for daughtercard EPROMs $26 plus shipping for 6 EPROM sets $45 plus shipping for 12 EPROM dual game sets I can supply complete lineup of known Vs. game chipsets. Identical copies of original ROMs, all tested on original hardware before shipping. Please stay tuned to this page for more great updates Title: Nintendo VS products and Services from PC-10.com Post by: Joe3693 on November 30, 2020, 02:46:38 pm Vs Goonies/Vs Gradius Combination Daughtercard
This brand new product allows you to load both games at the same time on a single side of a Nintendo Vs board! Just flip a switch and press a button and you can switch to play either Vs Goonies or Vs Gradius. This daughtercard is fully assembled, tested and working prior to shipping. All you have to do is install your existing CPU and PPU into the sockets and then install this onto your main Vs PCB. The pins used on this card are very similar to the ones used in original daughterboards. We opted to use these because they are much more robust than round machine pins and hold up much better when installed and removed from sockets over time. Once installed on your main board, allow 30 seconds for the game to boot when the daughtercard is installed. To change games, simply flip the toggle switch and then hold the reset button for 2 seconds. The game will reset and the other game will boot. Super simple! Each daughtercard is $115 shipped within the US. International shipping is additional. We also have a limited supply of Nintendo CPUs (RP2A03) available at the moment for an additional $22 (when purchased with a daughtercard) and will arrive pre-installed on the daughtercard. We do not have a source for PPU’s so you will have to supply that item. Simply tell us which Vs PPU you plan to install and your card will be custom configured based on your selection. All combination daughtercards will come with a remote-wired toggle switch and push button switch that are easily plugged into the board. However, if you would like a daughtercard configured to only play one game (instead of the combination), we can fulfill those custom requests as well. (https://uploads.tapatalk-cdn.com/20201130/14a9b2dad7811339c6e0f62cb98a2c49.jpg) (https://uploads.tapatalk-cdn.com/20201130/ff7e983c240a63a7d9c5dc22f831092b.jpg) (https://uploads.tapatalk-cdn.com/20201130/b4527a0416a32a2c3c74c39d2afd3281.jpg) (https://uploads.tapatalk-cdn.com/20201130/b9765bf06b5591c1ffac15cb1acd5fa4.jpg) (https://uploads.tapatalk-cdn.com/20201130/9b6fb1d79bd09d14aaa2aa9a9cd16f4d.jpg) (https://uploads.tapatalk-cdn.com/20201130/26d4326c054ff5ce82307bc45285ca87.jpg) |