|
Title: Stuck screws Post by: Low_crawl on October 26, 2016, 09:58:01 pm For the love of God does anyone have a tip to remove the larger screws from the monitor chassis?
Capping the monitors and trying to get the screws out so I can cap the board. There are two that are stuck and won't budge for anything! Sent from my SAMSUNG-SM-G900A using Tapatalk Title: Re: Stuck screws Post by: mrdude on October 26, 2016, 10:29:32 pm Larger bit? Vice grips? Put a screw driver on and tap it with a hammer? I save WD-40 and PB Blaster for cars typically. You're talking about the two that typically hold a chassis in so it can slide out? Worst case scenario is to take the monitor out and put the tube face down on a towel so you can get some leverage. I've been there...just with rusty bolts on cars. Good luck.
Title: Re: Stuck screws Post by: John's Arcade on October 26, 2016, 10:35:52 pm What monitor? Photo?
Title: Re: Re: Stuck screws Post by: Low_crawl on October 27, 2016, 10:17:46 am What monitor? Photo? The red tent montors. The two screws on the front under the adjustment pots and the two on the bottom (so I can remove the board to re cap it.I tried solvent, heat gun, different screw drivers, tapping them, moving the monitor for leverage. They are rounded so I can't grab them with vice grips. I'll grab a pic at lunch. Sent from my SAMSUNG-SM-G900A using Tapatalk Title: Re: Stuck screws Post by: Low_crawl on October 27, 2016, 12:38:10 pm (http://uploads.tapatalk-cdn.com/20161027/deb55be6a1ab45d93b480b077172bde7.jpg)(http://uploads.tapatalk-cdn.com/20161027/8b5207a6419cff097353a33559041062.jpg)(http://uploads.tapatalk-cdn.com/20161027/4e987f602912b1d5c10dc2e232706c73.jpg)
Sent from my SAMSUNG-SM-G900A using Tapatalk Title: Re: Stuck screws Post by: John's Arcade on October 27, 2016, 07:46:31 pm I don't really know what to say about this. SCREWDRIVER?!?!
Title: Re: Stuck screws Post by: Terry68Firebird on October 28, 2016, 06:26:29 am I don't really know what to say about this. SCREWDRIVER?!?! nah thats too mainstream, exactly what the screw thinks we are going to do, c'mon people think outside the box! ;D Title: Re: Re: Stuck screws Post by: Low_crawl on October 29, 2016, 11:12:40 am I don't really know what to say about this. SCREWDRIVER?!?! John, you know how frustrating your Tempest is right now? That's where I am with the damn screws. Most broke loose easy as pie. For some reason these four will not budge.I braced the monitor and actually got on top of it with my full body weight trying to break these things loose. I'm going to get a Dremel and just grind the bastards. It looks like they used some kind of green colored lock tight on these at the factory and someone was over zealous. I tried heat, torque, tapping, solvent, lube channel locks and everything under the sun. I was hoping someone had a moment of insight during a red tent restore. Sent from my SAMSUNG-SM-G900A using Tapatalk Title: Re: Stuck screws Post by: Terry68Firebird on October 29, 2016, 10:00:11 pm jsut found this tip-good luck ;)
To improve your screwdriver’s grip on the head, insert a wide rubber band between the screwdriver and the screw head. Place the rubber band flat against the head and insert your screwdriver. Slowly turn the screw driver and attempt to remove the screw Title: Re: Post by: Low_crawl on October 30, 2016, 12:10:30 pm Bought a grinder today, but I'll give it a shot Terry. Thank you my friend!
Sent from my SAMSUNG-SM-G900A using Tapatalk Title: Re: Post by: Low_crawl on November 03, 2016, 07:53:29 pm The grinder was a success!
Sent from my SAMSUNG-SM-G900A using Tapatalk Title: Re: Stuck screws Post by: John's Arcade on November 04, 2016, 11:10:14 am Woot!
|