Title: 3D Print Sega Part POW-2610 for Power Drifts brake, and gas pedal Post by: Blimpcity on January 21, 2015, 10:10:01 am If you can't find an old arcade part draft it and 3D print it! Sega part POW-2610 for Power Drifts brake, and gas pedal. My teeth are just a hair off, going to redesign it with wider teeth to reduce stress. Current teeth are .125" wide and there is room for them to be .4" wide.
(https://farm8.staticflickr.com/7483/16307811006_98d3962782.jpg) (https://flic.kr/p/qR4N4h)10943721_10203553248252811_4371405070185391029_n (https://flic.kr/p/qR4N4h) by Blimpcity1977 (https://www.flickr.com/people/127431729@N02/), on Flickr Title: Re: 3D Print Sega Part POW-2610 for Power Drifts brake, and gas pedal Post by: Blimpcity on January 21, 2015, 01:43:57 pm I drew up a modified gear so you can just swap the teeth out without taking the whole gas and brake assemble apart to swap teeth. Also its much cheaper to print just the teeth.
(https://farm9.staticflickr.com/8584/16333320801_f5b0269f6f.jpg) (https://flic.kr/p/qTjxek)POW-2610 Rev1 (https://flic.kr/p/qTjxek) by Blimpcity1977 (https://www.flickr.com/people/127431729@N02/), on Flickr Title: Re: 3D Print Sega Part POW-2610 for Power Drifts brake, and gas pedal Post by: Worm2 on January 22, 2015, 07:17:58 pm I drew up a modified gear so you can just swap the teeth out without taking the whole gas and brake assemble apart to swap teeth. Also its much cheaper to print just the teeth. (https://farm9.staticflickr.com/8584/16333320801_f5b0269f6f.jpg) (https://flic.kr/p/qTjxek)POW-2610 Rev1 (https://flic.kr/p/qTjxek) by Blimpcity1977 (https://www.flickr.com/people/127431729@N02/), on Flickr WOW! I am impressed. Is there a way to make the teeth stronger? Can you add extra supports? Would that even work? Title: Re: 3D Print Sega Part POW-2610 for Power Drifts brake, and gas pedal Post by: Blimpcity on January 26, 2015, 09:23:37 pm Shouldn't need more supports. I printed out my new design, and will install it and test it out for awhile.
(https://farm8.staticflickr.com/7528/16346297022_916e3e0495_n.jpg) (https://flic.kr/p/qUt3Bh)FullSizeRender (2) (https://flic.kr/p/qUt3Bh) by Blimpcity1977 (https://www.flickr.com/people/127431729@N02/), on Flickr (https://farm8.staticflickr.com/7535/16345429061_6532b4a575_n.jpg) (https://flic.kr/p/qUoAAr)FullSizeRender (1) (https://flic.kr/p/qUoAAr) by Blimpcity1977 (https://www.flickr.com/people/127431729@N02/), on Flickr Title: Re: 3D Print Sega Part POW-2610 for Power Drifts brake, and gas pedal Post by: darkcat1 on January 31, 2015, 12:18:42 pm nice going. I hope it holds up under stress because I heard the current material they use in 3D printers isn't really good for that
|